Conductivity Electrodes
Cole-Parmer Hach 3422C3A Contacting Conductivity Cell, 1000 ohm Pt RTD, titanium, K=1.0
Nonmetallic Ryton PPS cells 19065-55 and -57 have graphite electrode with 34" NPT(M) threads for mounting onto a 34" pipe tee or immersion applications. Sensor includes built-in 1000 Pt RTD and 20-ft (6-m) cable. PVDF cells 19065-60 through -68 have titanium electrodes with either 12" or 34" NPT(M) compression fitting for mounting onto a pipe tee with up to four inches of insertion depth. Reversing the compression fitting enables the sensor to be fastened onto the end of an immersion pipe. Cells include built-in 1000 Pt RTD and 20-ft (6-m) cable.
Cole-Parmer Conductivity Probe, 2-cell, K = 10.0, Epoxy Body/Pt Bands, 2.5-ft Cable
Keep your multiparameter meters up and running with replacement conductivity probes.
Cole-Parmer Oakton Flat-Surface Conductivity Probe, K = 1.0, 1 m Cable
If your conductivity measurements are off, you might need a new cell, sensor, or calibration kit. Update, upgrade, or replace to get the best out of your Oakton conductivity, resistivity, or TDS meter.
Hach Company Probe Cable Depth Markers for Rugged IntelliCAL Probes
Taking readings at specific depths with rugged outdoor electrodes is a snap with these depth markers. Visually identify the depth of your electrode by attaching depth marker securely on cable at points to meet your needs. Five markers per package.Note: For use with rugged outdoor electrodes only.
Hach Company Contacting Conductivity Sensor, Mid-Range Conductivity, K=1.0, 3/4" Kynar Compression Fitting
Nominal Cell Constant (K) = 1.0, 3/4 inch NPT Kynar (PVDF) Compression Fitting, 6m (20ft) Analog Cable, Titanium Electrode
Hach Company Radiometer Analytical CDC511T Conductivity Cell with Temperature Sensor (4-pole Pt sensor, k = 1.0 cm-1)
The Radiometer CDC511T is a 4-pole conductivity cell with non-platinized, platinum sensor (k = 1.0 cm-1), integrated temperature sensor and TPX body. The CDC511T sensor's 4 platinum ring design ensures results in general aqueous and non-aqueous media over several decades of conductivity with a single cell, using just one calibration. The CDC511T can be used with a flow-through cell for pure water measurements and meets requirements of USP 24-NF19. It has a fixed cable with MAB6 plug for use with Radiometer Analytical CDM210/230/92 conductivity meters.
Hach Company Sension+ 5062 portable titanium conductivity cell for “difficult” applications
Sension+ 5062 is a two-pole titanium conductivity cell with a titanium body and built-in temperature sensor. The 5062 has a fixed 1 meter cable and MP5 connector dedicated for use with Hach Sension+ Portable Conductivity meters. The 5062 is ideal for conductivity measurements in extreme conditions and for “difficult” applications, including dirty and viscous samples.
Andwin Scientific M-CELL 6/PK
The M-Cell or Six Pack is composed of six test kits. Each test kit has vacuum packed expendables that are used to conduct one test. This product also contains a container of distilled water to perform water separation tests.
Cole-Parmer Conductivity/Temp probe, K=0.1 for 6 and 6 series meters
Oakton Conductivity/Temp Probe, for 6 and 6+ Series Meters; K=0.1, If your conductivity measurements are off, you might need a new cell, sensor, or calibration kit. Update, upgrade, or replace to get the best out of your Oakton conductivity, resistivity, or TDS meter.
METTLER TOLEDO PROCESS ANALYTICAL INC COND SENSOR 1.5TRI 0.1C SS ISM
NC2051302 COND SENSOR 1.5TRI 0.1C SS ISM